43 Search Results

Algal biochar, as the solid residue of biofuel production from algal biomass, is reported to explore disposition options, aiming to lessen the liability or obstacles to biofuel production processes. However, landfills and open combustion lead to adverse environmental impacts. One way to add value to such wastes is to use them as admixtures in cementitious construction materials. This study aims to investigate the feasibility of algae-derived biochar as supplementary cementitious materials (SCM) at different water contents and mixture ratios. Algal biochar-cement composites were prepared with different algal biochar content as well as different water-to-cement (w/c) ratios, and the surface area,more » morphology, elemental, and mineralogical composition were characterized. To compensate for the high-water absorption of algal biochar, a small concentration of a superplasticizer was used since higher w/c ratios negatively impact strength. The mechanical performance of algal biochar-cement composites is compared with control composites using commercial silica fume as a typical commercial SCM. The findings suggest that algal biochar is a promising candidate to replace commercial SCM, like silica fume, since algal biochar-cement composites can reach comparable compressive strength and Young’s modulus to commercial pozzolan-cement materials with the same w/c ratio, though at later curing times, 33 days. Although the tensile strength of algal biochar-cement composites is statistically similar at 7 days, it is significantly lower at later curing times, and further investigation is required to improve this property. Algal biochar-based cement binders showed comparable embodied carbon to silica fume-based cement binders based on a cradle-to-gate lifecycle analysis. However, the ability of algal biochar to absorb large volumes of CO₂ over short periods of time, as measured in this study, makes this novel SCM an excellent alternative to reduce the embodied carbon of concrete structures cradle-to-grave at 1/10 of the cost. In conclusion, valorization of algae-derived solid waste provides great potential to reduce embodied carbon and brings credit to biofuel production and concrete-based construction.« less

Commercially pure aluminum alloy, AA1100, presents good electrical and thermal conductivity, high formability, and low cost. Those favorable characteristics have the potential to enable bipolar plates with improved economics and enhanced performance compared to current stainless steel bipolar plates for proton exchange membrane fuel cells. An accurate constitutive model is essential to develop and optimize processing parameters and effectively control the forming process. Here, the objective of this work is to develop a constitutive model of AA1100 that is able to simulate stress-strain relation, formed geometry, and predict the onset of fracture strain to avoid forming failure. Initially, a setmore » of tensile tests at temperature between 300 and 500°C and strain rate between 0.005 and 1.0/s were conducted to examine the deformation behavior. Then, a set of damage-based unified visco-plastic constitutive equations is proposed and calibrated based on the results of stress-strain data. A genetic algorithm optimization method is applied to search for best fitting material constants in constitutive equations. The proposed model shows good predictability of both the stress-strain relation and fracture strain at low strain rate and high temperature conditions. The accuracy of proposed model is also evaluated statistically. A comparison of the proposed model with three popular models (Arrhenius-type mode, Johnson-Cook model and Zerilli-Armstrong model) was made. The proposed model shows the best experimental agreement with correlation coefficient of 0.96 in contrast to 0.25, 0.38 and 0.75 for the popular models, respectively. The proposed model can help to optimize the elevated temperature forming process and guide die design to enable optimal geometric features in the formed components.« less

We evaluated the application of silica suspension injection and sequential gelation to block vertical water flow in the annuli of long-screened wells. First, we studied the viscosity, rheological behavior, and gelation performance of colloidal silica suspensions in batch tests. Then, we tested the injection of silica suspensions and the water flow blocking efficiency of the later formed silica gel in column and bench-scale sandbox experiments. Micron-sized fumed powder silica suspensions and nanosized silica suspensions recovered from geothermal fluids were tested in this work. Fumed silica suspensions showed shear thinning, while nanosized silica suspensions exhibited Newtonian flow behavior. During the gelationmore » process, the nanosized silica suspension changed from a Newtonian fluid to a shear thinning fluid while increasing its overall viscosity. At comparable concentrations, the nanosized silica suspensions have much lower viscosity than that of the fumed silica suspensions. Increases in the Na⁺ concentration and silica particle concentration in these suspensions shortened the gelation time. Silica suspension gelation in sand columns completely blocked the water flow and sustained the injection pressure up to 50 psig (344.7 kPa). A silica suspension was successfully injected into the target zone in the annulus of a bench-scale sandbox mimicking long-screened wells in the field. The silica gel formed in the annulus effectively blocked chemical transport through the gelled zone. Our research reveals that a process using silica suspension injection and sequential gelation technology is promising for blocking the vertical water flow and chemical transport through the filter pack in targeted zones within the annulus of long-screened well systems.« less

Here, this article presents an overview of the current state of the art in the structure determination of microporous carbon-capture materials, as discussed at the recent NIST workshop “Integrating Crystallographic and Computational Approaches to Carbon-Capture Materials for the Mitigation of Climate Change”. The continual rise in anthropogenic CO₂ concentration and its effect on climate change call for the implementation of carbon capture technologies to reduce the CO₂ concentration in the atmosphere. Porous solids, including metal–organic frameworks (MOFs), are feasible candidates for gas capture and storage applications. However, determining the structure of these materials represents a significant obstacle in their developmentmore » into advanced sorbents. The existing difficulties can be overcome by integrating crystallographic methods and theoretical modeling. The workshop gathered experimentalists and theorists from academia, government, and industry to review this field and identify approaches, including collaborative opportunities, required to develop tools for rapid determination of the structures of porous solid sorbents and the effect of structure on the carbon capture performance. We highlight the findings of that workshop, especially in the need for reference materials, standardized procedures and reporting of sorbent activation and adsorption measurements, standardized reporting of theoretical calculations, and round-robin structure determination.« less

Oxide dispersion strengthened (ODS) steels, traditionally fabricated by ball milling and conventional powder metallurgy techniques to achieve bulk form, followed by intricate rolling and thermal treatment steps to achieve plate or sheet form. Here, we present a novel processing route that combines cold spray (CS) with friction stir processing (FSP) to manufacture ODS steel plate directly from gas atomization reaction synthesis (GARS)-prepared powder, thus no rolling steps involved. Microstructural and mechanical characterizations were performed to assess the quality and properties of the resulting ODS steel plate. Our findings demonstrate that the slightly porous CS deposited layer was fully consolidated aftermore » FSP, yielding a fully dense ODS steel plate that exhibited a favorable tradeoff between strength and ductility upon extraction from the substrate. Furthermore, through microstructural analysis, we revealed the presence of an appreciable density (∼10²²/m³) of nano-sized oxide particles, with the majority being smaller than 5 nm via the combined CS + FSP fabrication route. This work serves as a first proof-of-concept demonstration of the manufacturing approach described herein, offering a possible alternative route for producing ODS steel plates.« less

Programmable self-assembly of dyes using DNA templates to promote exciton delocalization in dye aggregates is gaining considerable interest. New methods to improve the rigidity of the DNA scaffold and thus the stability of the molecular dye aggregates to encourage exciton delocalization are desired. In these dye–DNA constructs, one potential way to increase the stability of the aggregates is to create an additional covalent bond via photo-cross-linking reactions between thymines in the DNA scaffold. Specifically, we report an approach to increase the yield of photo-cross-linking reaction between thymines in the core of a DNA Holliday junction while limiting the damage frommore » UV irradiation to DNA. We investigated the effect of the distance between thymines on the photo-cross-linking reaction yields by using linkers with different lengths to tether the dyes to the DNA templates. By comprehensively evaluating the photo-cross-linking reaction yields of dye–DNA aggregates using linkers with different lengths, we conclude that interstrand thymines tend to photo-cross-link more efficiently with short linkers. A higher cross-linking yield was achieved due to the shorter intermolecular distance between thymines influenced by strong dye–dye interactions. Furthermore, our method establishes the possibility of improving the stability of DNA-scaffolded dye aggregates, thereby expanding their use in exciton-based applications such as light harvesting, nanoscale computing, quantum computing, and optoelectronics.« less

Organic dye aggregates have been shown to exhibit exciton delocalization in natural and synthetic systems. Such dye aggregates show promise in the emerging area of quantum information science (QIS). We believe that the difference static dipole (Δd) is an essential dye parameter in the development of molecular QIS systems. However, a foundational understanding of the structural factors influencing Δd remains elusive. Bacteriochlorins play a vital role in photosynthesis due to their exceptional photophysical properties. Therefore, bacteriochlorins are particularly suitable dyes for the construction of aggregate systems for QIS. Synthetic bacteriochlorins further offer stability and tunability via chemical modifications. Here, themore » influence of substituents on the Δd of monomeric (non-aggregated) dyes was investigated via density functional theory (DFT) and time-dependent (TD-)DFT in a set of 5-methoxybacteriochlorins progressively substituted with ethynyl, phenyl, and phenylethynyl substituents at the 3,13- and 3,13,15-positions of the macrocycle. Symmetrically substituted 5-methoxybacteriochlorins were shown to have the largest Δd. The increase in Δd in the series of dyes was largely due to changes in orientation of the static dipole upon excitation rather than large changes in magnitude. In addition, the transition dipole (μ) and the angle between Δd and μ (ζ) were calculated. Three 5-methoxybacteriochlorins with high predicted Δd and μ were synthesized and characterized spectroscopically. The trend in Δd values empirically determined using the solvatochromic Stokes shift method was comparable with the DFT calculations.« less

Molecular aggregates exhibit emergent properties, including the collective sharing of electronic excitation energy known as exciton delocalization, that can be leveraged in applications such as quantum computing, optical information processing, and light harvesting. In a previous study, we found unexpectedly large excitonic interactions (quantified by the excitonic hopping parameter J_m,n) in DNA-templated aggregates of squaraine (SQ) dyes with hydrophilic-imparting sulfo and butylsulfo substituents. Here, we characterize DNA Holliday junction (DNA-HJ) templated aggregates of an expanded set of SQs and evaluate their optical properties in the context of structural heterogeneity. Specifically, we characterized the orientation of and J_m,n between dyes inmore » dimer aggregates of non-chlorinated and chlorinated SQs. Here, three new chlorinated SQs that feature a varying number of butylsulfo substituents were synthesized and attached to a DNA-HJ via a covalent linker to form adjacent and transverse dimers. Various characteristics of the dye, including its hydrophilicity (in terms of log P_o/w) and surface area, and of the substituents, including their local bulkiness and electron withdrawing capacity, were quantified computationally.« less

Nanoscale dye-based excitonic systems assembled on DNA origami in solution excited by a laser. Dyes engage in cascaded FRET with exciton movement guided by programmed elements engaging in homo- and hetero-energy transfer.

Dye molecules, arranged in an aggregate, can display excitonic delocalization. The use of DNA scaffolding to control aggregate configurations and delocalization is of research interest. Here, we applied Molecular Dynamics (MD) to gain an insight on how dye–DNA interactions affect excitonic coupling between two squaraine (SQ) dyes covalently attached to a DNA Holliday junction (HJ). We studied two types of dimer configurations, i.e., adjacent and transverse, which differed in points of dye covalent attachments to DNA. Three structurally different SQ dyes with similar hydrophobicity were chosen to investigate the sensitivity of excitonic coupling to dye placement. Each dimer configuration wasmore » initialized in parallel and antiparallel arrangements in the DNA HJ. The MD results, validated by experimental measurements, suggested that the adjacent dimer promotes stronger excitonic coupling and less dye–DNA interaction than the transverse dimer. Additionally, we found that SQ dyes with specific functional groups (i.e., substituents) facilitate a closer degree of aggregate packing via hydrophobic effects, leading to a stronger excitonic coupling. This work advances a fundamental understanding of the impacts of dye–DNA interactions on aggregate orientation and excitonic coupling.« less